Saws-Vertical

bullet

DeWalt Monarch 20 ", model 72B 30, 10" x 20" throat, 1" blade cap, 1hp 110/220/1ph, 136" blade length (PHOTO)........$1,800

bullet

DoAll ML 16", Vertical, 110v, Chain pull thru setup, side mitering gauge, Blade welder, Vari speed Hi/Lo range ................$3,400

bullet

DoAll 20", Model 2013-10, S# 339-78946, 1" Blade Welder, variable speed with high/low range, 50 to 5200 fpm, 26" x 26" tilting table, 3hp 230/460/3ph wired 230 (PHOTO)............$4,250

bullet

DoAll 20" Zephyr, 32" x 40" Hydraulic table, T-slotted, coolant, chip blower, blade welder 1.5" 8kva, 3 speed trans, S# 32-51273, 7.5hp 220/440/3ph (PHOTO)................$4,900

bullet

DoAll 26-6 12"x 26" blade welder, hyd. feed (PHOTO)........$3,000

bullet

DoAll 36" zephyr, three speed (PHOTO1) (PHOTO2).......$8,000

bullet

DoAll 36W 36" x 20", 1" blade, coolant, light ..........$4,500

bullet

DoAll, 36" Throat depth, Model 3618-3, S# 153-721141, 64" x 39" Table, 35.0 Instant amps, 4.6 Normal amps, 440/3ph 60cyc, Band length max 191, Belts make DOALL, Motor Variable D2878, Variable Trans. D35-2306, Air pump D3954, Elect. Schematic # 403431, Hyd. Schematic # 58362-0, 3 speed lo/med/hi 25 - 6,000 FPM, Overall Dimensions (Saw) 93"H x 71"L x 37"W, (Table) 48.5"H x 57"L x 148"W (PHOTO1) (PHOTO2) (PHOTO3) (PHOTO4) (PHOTO5) (PHOTO6) (PHOTO7) (PHOTO8)...........$9,500

bullet

Marvel 18" Model 81A, Fully hydraulic, power tilt to 45 deg, model 81A11-PC, S# 460011 new in 94, 1.25" Blade, 10hp 230/460/3ph, blade speed 18 to 400 fpm, Cleaned & Painted, just purchased (PHOTO1) (PHOTO2) (PHOTO3) (PHOTO4) (PHOTO5) (PHOTO6) (PHOTO7)......................$34,500

bullet

Marvel 18" Model 81A, With Auto In feed table, Fully hydraulic, Programmable control for infeed, power tilt to 45 deg, model 81A10-PC, S# E394110PC new in 84, 1.25" Blade, 10hp 230/460/3ph, Just Purchased (PHOTO1) (PHOTO2) (PHOTO3).........P.O.R.

bullet

Marvel 18", Model # 8, S# 81862, 6 speed, tilting arm to 45 deg for mitering, Powered in feed, 3/4" blade, coolant with trays, cleaned and painted  1.5hp/ 3/4Hp 2 speed motor 208v 3ph. (PHOTO1) (PHOTO2).................$5,500

bullet

Marvel 25" Hydraulic Production type, model 25/M4/S1/S2, S# E-16425, new in 82, Chip Conveyor, coolant, 20hp (PHOTO1) (PHOTO2) (PHOTO3) (PHOTO4) (PHOTO5)................... Just Purchased $29,000

bullet

Marvel No. 8, Model No. 8, S# 81862, Normal capacity 18" x 18", Max 21" x 18 1/2", Maximum capacity with blade at 45deg 14 1/4" & 18 1/2" depth, Has sliding indicator to set feed pressure 0 to 8 settings, Manual operated 12" x 6" quick release type vise clamps, Both jaws can be moved forward or back on 3/4" T slots on table by mean of ratchet dogs, Can be shifted to either side of blade for cuttong on either the left or right hand side, And are reversible to bring the angular sides close to the blade when mitering either right or left, or be removed entirely, leaving the machine table clear to fasten fixtures of work of irregular shapes. Saw table 32"W x 5'L x 32"H, has four 3/4" T slots, the 2 center ones machined and notched to hold vise jaws. Blade dim. 14' 8" x 3/4", 6 Blade speeds 40-58-80-100-115-200, 12 Gallon coolant drip/chip catch pan reservoir, Maximum swing of column and blade from vertical 45 deg., Motor 1.5hp 220v 3ph 870 to 1,740 rpm, 2 speed range variable with high & low control switch, Over all dim. 36"W x 78"L x 84"H, Est. Wt. 2,200 lbs. (PHOTO1) (PHOTO2) (PHOTO3) (PHOTO4) (PHOTO5) (PHOTO6) (PHOTO7) (PHOTO8) (PHOTO9) (PHOTO10) (PHOTO11) (PHOTO12)..........................................$5,500

bullet

Powermatic 20", model -87, S# 687401, 1" blade cap, Variable speed from 47 to 5,200 fpm with 2 ranges, 12" high work height in throat, pull through feed setup via cable & counter weight setup, 1" blade welder with grinder (PHOTO)...................$2,900

bulletPower-Matic Vertical 20" Band Saw, Model # 87, S# 8487030, Vari Speed 750 to 5,200 RPM, Blade Length Max. 12' 7" Min. 12' 5", w/light (PHOTO1) (PHOTO2) (PHOTO3) (PHOTO4) (PHOTO5).................$2,400
bullet

Startrite 15.5", model 216H, S# 15004, 12.5" throat height, Hydraulic Infeed on table, 26" x 26" tilting & T slotted table, 1" Blade welder, variable speed, 3hp 220/440/3ph wired 220v (PHOTO)................$3,900 Sale Price $3,500

bullet

Stammets 36" x 16" hydraulic table, 3 speed, welder, tach (PHOTO)..........$6,800

bullet

Tannewitz DiSaw 36", S# 7939, 36" x 40" table / tilts to 45, speeds 50 to 800 fpm, air chip blower, variable speed, blade welder, 36" x 16"H throat  1hp 220v 3ph. (PHOTO1) (PHOTO2)..........$2,750

bullet

Tannewitz DiSaw 36", S# 7936, 36" x 40" table / tilts to 45, speeds 50 to 800 fpm, air chip blower, variable speed, blade welder, table 90 deg Guide, 36" x 16"H throat  1hp 220v 3ph. (PHOTO1) (PHOTO2).........$2,750

bullet

New Wilton 14" Tradesman Band saw good for wood or metal, 8 speed 39 to 3,000 fpm, model 8201, 1hp 115/230/1ph (PHOTO).......$1,100

BACK to INDEX

VISIT OUR E-BAY STORE

E-mail address: Sales@interplantsales.com

Hit Counter